Home > About us > FAQ > How to install a LED high bay light?

FAQ

How to install a LED high bay light?
2013-12-13 23:47:34
Download
Used for in-door & out-door, eg. the workshop, the storehouse, the road toll station, the gas station, the large-scalsupermarket, the exhibition hall, the stadium and so on which need lighting
LED high bay light applications:
Used for in-door & out-door, eg. the workshop, the storehouse, the road toll station, the gas station, the large-scale supermarket, the exhibition hall, the stadium and so on which need lighting
3. Using instructions
 

3. LED high bay light Using instructions

1. Working voltage: AC85-265V/277V  50-60Hz, Do not exceed the operating voltage.
2. Storage temperature:-25℃ ~ +65℃。 Working temperature: -40℃~+55℃。 Best working temperature: -0℃ ~ +30℃
3. The reflector of the light is easily deformed, so please handle with care and no press hard during transportion or storage.
 
3. Maintenance & repair instructions
4. LED high bay light Maintenance & repair instructions
1) 、Troubles resolution:
        Troubles and solutions: Observe the surface of LED light source whether there is discoloration, broken traces, with or without obvious fracture connectivity when you check. Please also check whether Power connection is loose & short-circuit, with or without obvious signs of damage. Please replace the light source and power if there is any obvious signs of damage.
2. Maintenance, repair Note
1)、 Please make sure the power-off before maintenance.
2)、 In order to maintain a good light transmittance, please clean the reflector of the industrial light regularly.
3)、 For maintaining good heat dissipation, please clean the dust on shell and the heat sink of the industrial light timely.
4)、 Please do not use water or corrosive cleaning liquor to clean, preferably with a dry cloth.
5)、 You may open the rear cover with a screwdriver, cut off the power when you replace the power supply.
 
     About the AC power three-pin wire, the bronw one is "L", the blue one is "N", the green&yellow one is Ground line. Regarding DC power wire, the red or white lines correspond to anode, and the black line corresponds to cathode. Please don't reverse the anode and cathode.
2. Maintenance, repair Note
1)、 Please make sure the power-off before maintenance.
2)、 In order to maintain a good light transmittance, please clean the reflector of the industrial light regularly.
3)、 For maintaining good heat dissipation, please clean the dust on shell and the heat sink of the industrial light timely.
4)、 Please do not use water or corrosive cleaning liquor to clean, preferably with a dry cloth.
5)、 You may open the rear cover with a screwdriver, cut off the power when you replace the power supply.
 
     About the AC power three-pin wire, the bronw one is "L", the blue one is "N", the green&yellow one is Ground line. Regarding DC power wire, the red or white lines correspond to anode, and the black line corresponds to cathode. Please don't reverse the anode and cathode.
 
Get more information about TEK Lighting LED high bay industrial light, please contact us.
LED lamp not bright Lamp wire connection is abnormal Loosen the screw and reconnect the power supply wire
LED is damaged Replace the LED
Power supply failure Replace the power supply
LED lamp twinkled Power supply connected well Loosen the screw and reconnect the power supply wire
Input voltage waves large Confirm the right input voltage
Power supply failure Replace power supply
1. Working voltage: AC85-265V/277V  50-60Hz, Do not exceed the operating voltage.
2. Storage temperature:-25℃ ~ +65℃。 Working temperature: -40℃~+55℃。 Best working temperature: -0℃ ~ +30℃
3. The reflector of the light is easily deformed, so please handle with care and no press hard during transportion or storage.
 
2. Storage temperature:-25℃ ~ +65℃。 Working temperature: -40℃~+55℃。 Best working temperature: -0℃ ~ +30℃
3. The reflector of the light is easily deformed, so please handle with care and no press hard during transportion or storage.

Previous   [Return Home] [Print] [Go Back]   Next

Contact Us

  • Contact Person:

    Jenny Wei
  • Tel:

    0086-755-2305 1282
  • 0086-150-1411-5394
  • Fax:

    0086-755-6682-2827
  • E-mail:

    sales@ledcornbulbs.com
  • Contact QQ